Weathering of wood is a combination of chemical, mechanical, biological, and sunlight-induced processes that change the appearance and structure of wood. After two months of exposure, all woods will turn yellowish or brownish and then gray. Dark woods will become lighter; light woods eventually darken. Surface checks, raised grain, cupping, and warping all develop as wood continues to weather.
Recent research conducted by the Forest Products Laboratory indicates that failure to properly treat new lumber can reduce the average life of wood by 20 percent. Understanding the differences between finishes makes it easier to select the right product. In the past, finishes were made from alkyd or natural oil resins, such as linseed, tung, soya, and paraffin. The resins were often blended with waxes to provide additional water repellency, and then diluted with a mineral spirits solvent.
Technological advances and environmental regulations on emission levels of volatile organic compounds (VOC's) have spurred the development of new products. Water-based products, particularly those formulated with certain water-reducible synthetic oils and resins, have excellent penetration and perform as well as, or better than, oil-based (alkyd) finishes. The performance of commercially available wood finishes is often listed on a product label or in literature supplied by the manufacturer. The American Society for Testing and Materials (ASTM) has standardized test methods to measure the water repellency and color retention of wood finishes. In ASTM test D5401-93, a finish is applied to a 2" by 4" section of wood, allowed to cure for seven days under controlled conditions, and then tested for water absorbency.
Standard ASTM G53-88 evaluates the water repellency of coatings exposed to ultraviolet light and condensation in a weather exposure chamber for 1000 hours. Manufacturers also use outdoor tests to measure weathering in various climates, and they might provide test results if you request them. Finishes are generally classified into two basic categories: those that form a film or coating on wood, and those that penetrate.
These products form a coating, or film, that is a barrier between wood and the elements. Film-formers include many alkyds, latex/acrylics, and varnish resins in solvent or water-based finishes. Products without pigments are considered to be a clear or transparent finish, and have little or no protection from ultraviolet (UV) radiation. Pigments are added to paints, solid color stains, and semi-transparent finishes to change the appearance of the wood and to provide protection from UV rays.
Some of the newer water-based coatings are semitransparent acrylic blends that have excellent flexibility. Unfortunately, due to their higher molecular weight, acrylics still form a film on the surface of wood, and are subject to the cracking that is a characteristic of all film-forming finishes. A film finish cracks as wood expands and contracts during normal moisture cycling and water gets underneath the finish and deteriorates the wood. Removing film-forming wood finishes can be difficult, but is often necessary before re-application. If the failing coat is not removed, then the new coat may blister and peel.
Penetrating wood finishes are oil or water-based products that saturate wood pores to prevent water penetration. They typically contain a drying oil or resin in a transparent or semitransparent stain. Advantages of penetrating finishes over films are that they provide long-term water repellency, they don't trap moisture in the wood, and they do not peel or blister. Natural oils (linseed and tung, for example) are initially very effective in stopping the absorption of water into wood, but tend to darken over time because they are a food for fungi. Buildings treated with natural oils and resins generally need extensive cleaning before reapplying the finish.
Some of the newer water-based systems have synthetic oils and resins and they provide excellent water repellency and color retention. One of the main advantages of synthetic resins is that unlike natural oils, they do not serve as a food for most biological growth, making future coats easier to apply.
Correct application is critical to performance. Follow the manufacturers' instructions, particularly with the newer water-based formulations. All finishes should be applied to a clean surface, but penetrating finishes must be applied to surfaces that are porous and free from previous coatings. Although chlorine bleach will effectively remove many stains like mold and mildew, it can damage wood and is toxic to people and plant life. Newer, chlorine-free cleaners are environmentally safe and can actually increase product penetration up to 25%.
Wood that is pre-treated with a cleaner or pressure washer will probably have some have better finish penetration.Water-based finishes tend to dry faster than oil-based products. To avoid lap marks, particularly on hot sunny days, apply these only in the shade: the cooler surface will absorb better and allow for easier application of a second coat.
Routine maintenance is necessary, but the life-span of a finish depends on a variety of factors. Construction details, exposure to the elements, product choice, surface preparation, and application techniques are all essential to success. Some finishes may even require chemical stripping or sandblasting to restore wood to the proper condition before re-treatment. Finishes that weather unevenly and are re-coated without removing the old finish will have an unsightly, patchy appearance.
Although the wood finish is only a small percent of the cost of a log home, it is one of the more critical elements in construction. To most consumers, aesthetic appeal is just as important as performance when selecting a wood finish. Understanding the properties and expected performance of various products makes the decision process much easier for you.